ASTM A516/A516M Grade 65 [Grade 450] · plate selection and purchase requirements

Buying A516 Grade 65 plate for a specified vessel design

Gangsteel supplies ASTM A516 Grade 65 carbon-manganese pressure vessel plate. The specification addresses welded pressure vessels in moderate and lower temperature service where notch toughness is important. For the buyer, choosing Grade 65 means ordering the material called for by the design—not simply choosing a lower number than Grade 70.

A useful enquiry begins with the drawing or material schedule. Identify ASTM A516/A516M, the required edition, Grade 65 in inch-pound units or Grade 450 in SI, and the dimensions and quantity. The two unit systems have independent standard values and must not be mixed as exact conversions.

Define plate size and delivery condition together

List thickness, width, length and quantity for each plate item, with the dimensional tolerances and identification required by the project. Keep different thicknesses as separate enquiry lines: the applicable carbon maximum and delivery requirements need to be assessed for each item. Include the requested delivery destination and date on the same schedule so the enquiry covers the full order.

Public specification compilations describe plates over 1.50 in. [40 mm] as normalized unless otherwise ordered, and plates at or below that boundary as normally as-rolled unless ordered otherwise. For the thinner range requiring notch-toughness testing, those references specify normalizing unless the purchaser specifies otherwise. Apply the wording in the ordered edition and unit system.

If normalized plate is required at any thickness, state that explicitly alongside any Gr.65+N shorthand. The 50 mm carbon-composition step is not the 40 mm delivery-condition boundary. Neither a normalized suffix nor a pressure-vessel description supplies an order-specific impact-test result.

Grade 65 chemistry: thickness and analysis basis

These public-reference chemical limits are in mass percent for Grade 65 [450], not mill typical values or a producer’s tighter guarantee. Heat analysis concerns the steel heat; product analysis uses a finished-product sample. The carbon maxima below apply to both, while manganese and silicon have separate heat and product ranges.

Grade 65 carbon maxima, mass % — public reference
Plate thickness Heat analysis Product analysis
½ in. [12.5 mm] and under 0.24 0.24
Over ½ in. to 2 in. [12.5 to 50 mm], incl. 0.26 0.26
Over 2 in. to 4 in. [50 to 100 mm], incl. 0.28 0.28
Over 4 to 8 in. [100 to 200 mm], incl. 0.29 0.29
Over 8 in. [200 mm] 0.29 0.29
Grade 65 other elements, mass % — public reference
Element Heat analysis Product analysis
Manganese 0.85–1.20 0.79–1.30
Silicon 0.15–0.40 0.13–0.45
Phosphorus, maximum 0.025 or 0.035; see edition note 0.025 or 0.035; see edition note
Sulfur, maximum 0.025 or 0.035; see edition note 0.025 or 0.035; see edition note

Use “and under” and “Over” within the order’s unit system at the ½ in. [12.5 mm] boundary. The manganese ranges shown apply in both the thinner and thicker bands for this grade; silicon is not thickness-dependent in the consulted tables.

Carbon–manganese adjustment: for each reduction of 0.01 percentage point below the specified carbon maximum for that thickness, an increase of 0.06 percentage point above the manganese maximum is permitted, up to 1.50% by heat analysis and 1.60% by product analysis.

Phosphorus and sulfur: identify the applicable edition

For phosphorus and sulfur, the reference source matters as much as the number.

  • 0.035% appears for both analyses in public tables identified with ASTM A516/A516M-06 and SA-516 described as identical with that edition.
  • 0.025% appears for both analyses in public compilations, including a January 2022 compilation without an ASTM year and compilations citing A516/A516M-25. It is not presented here as a confirmed official value of any named current ASTM or ASME edition. These references do not establish which edition introduced it.

Use the limits in the edition named on the order. A mill’s tighter product guarantee or a lower reported result does not redefine the specification limit; any additional restriction belongs in the purchase requirements.

Strength requirements and elongation test basis

The tensile ranges below come from the official ASTM A516/A516M-25 public Scope. Yield and elongation are supported by SSAB’s published Grade 65 required properties. These references help prepare an enquiry; acceptance follows the ordered specification. The elongation figures describe gauge lengths, not two plate-thickness classes.

Grade 65 [Grade 450] mechanical properties — public reference
Property Published reference value Basis / conditions
Tensile strength, Grade 65 65–85 ksi Inch-pound; ASTM A516/A516M-25 public Scope.
Tensile strength, Grade 450 450–585 MPa SI; ASTM A516/A516M-25 public Scope.
Yield strength, minimum 35 ksi Inch-pound; SSAB Grade 65 required-property table.
Elongation, minimum, 2 in. [50 mm] gauge 23% SSAB required properties; thickness adjustments under A20/A20M.
Elongation, minimum, 8 in. [200 mm] gauge 19% Same test basis and applicable thickness adjustments.

Use the SI yield minimum stated in the ordered edition rather than converting 35 ksi. Apply the relevant A20/A20M elongation adjustments for thickness. Any impact requirement needs its own temperature, specimen orientation and acceptance criteria.

Related designations when the material schedule changes

Grade 65 selection context — no automatic substitutions
Material / designation Relationship to this purchase
ASTM A516 Grade 60 steel plate Another strength grade in A516/A516M; a design change is not a purchasing substitution.
ASTM A516 Grade 70 steel plate Higher specified tensile range, 70–90 ksi [485–620 MPa], and inch-pound yield minimum 38 ksi, compared with Grade 65’s 35 ksi. Carbon limits also differ.
ASME SA516 Grade 65 steel plate Corresponding ASME designation for Code work; the required designation, edition and certification must be specified.
ASTM A515 Grade 65 A different specification for intermediate- and higher-temperature service, not the same material merely because the grade number matches.

For another ASME material schedule, see ASME SA516 Grade 60 steel plate or ASME SA516 Grade 70 steel plate as separate grades. Changes to strength level or standard require the applicable design and Code review; these pages do not authorize interchangeability.

Inspection scope for the plates being purchased

Include ultrasonic examination requirements with the enquiry, naming the method, standard edition, acceptance requirements and report scope. Where ASTM A435, A577 or A578 is specified, the number alone is not a complete inspection instruction. Testing and document arrangements need agreement for the order.

Identify required material documents, heat-number traceability, marking, delivery-condition records and test reports. Product analysis or impact testing should be named where required rather than inferred from the grade description. Align the document list with the project’s receiving inspection so that results can be assessed on the correct basis.

Grade 65 purchasing questions

Can Grade 70 be supplied against a Grade 65 order?

Not as a routine substitution. Grade 70 has different specified strength and carbon limits, even though it belongs to the same A516 family. A change must be accepted through the project’s design and material-approval process. Keep the originally specified grade on the enquiry until any revision is formally agreed.

Why is there more than one carbon maximum?

The maximum depends on plate thickness. For example, 0.24% belongs to the thinnest Grade 65 band, not every plate. Select the row for the ordered thickness in the chosen unit system. A reported heat analysis is the actual result for that heat, rather than a replacement for the applicable limit.

Should product analysis use the heat-analysis manganese range?

No. The published references distinguish the two analysis bases, including different manganese and silicon ranges. Establish whether the document reports heat or product analysis before assessing the result. Apply the ordered edition and any agreed additional restrictions; do not reject or accept a result by switching between the two ranges.

Does Gr.65+N include a Charpy test?

The suffix communicates normalizing, not an agreed Charpy test programme. If impact testing is required, provide the temperature, orientation and acceptance criteria, together with the governing specification or project requirement. Request the corresponding results in the material documents rather than relying on the normalized designation as proof of impact performance.

What should accompany a mixed-size enquiry?

Send an itemized plate list with thickness, width, length, quantities and tolerances, plus the material specification and edition. State delivery condition and inspection requirements by item where they differ. This lets the quotation address the actual purchase instead of leaving different sizes and test conditions under one undifferentiated grade description.

Send Gangsteel an itemized Grade 65 enquiry

Please provide the purchase details that apply to your material schedule:

  • ASTM A516/A516M edition, grade and unit system.
  • Plate dimensions, quantities, tolerances and requested delivery destination.
  • Required delivery condition and any additional chemistry restrictions.
  • Impact and ultrasonic requirements, material documents and marking.
  • Requested delivery date for assessment against the proposed supply.

Include the drawing or project specification where it defines requirements beyond the grade name.

Contact us

Availability, document scope and delivery terms are subject to the quotation for the specific order.

ASTM A516 Grade 65|ASTM A516GR.65 steel plate