ASME SA516 Grade 65, also commonly written as SA516GR.65, SA-516 Grade 65, SA516 GR 65 and ASME SA-516/SA-516M Grade 65 [Grade 450], is the ASME family designation corresponding to ASTM A516/A516M Grade 65 [Grade 450]. Grade 450 is the SI designation in the same family, not a converted Grade 65 value. ASTM A516 Grade 65 is the corresponding ASTM designation, not merely another spelling of the ASME name. An ASTM-only certificate does not automatically satisfy a specified SA-516 order, and the reverse is also true. The official product page is ASME SA516 Grade 65.
This page states the published tensile, yield and elongation figures for ASME SA516 Grade 65 [Grade 450]. These are the official public-reference mechanical properties already disclosed on ASME SA516 Grade 65 and ASTM A516 Grade 65. Inch-pound Grade 65 and SI Grade 450 values are independent and are not converted from one another on this page.
ASME SA516 Grade 65 Mechanical Properties
| Property | Published reference value | Basis / conditions |
|---|---|---|
| Tensile strength, Grade 65 | 65–85 ksi | Inch-pound; ASTM A516/A516M-25 public Scope, as used on ASTM A516 Grade 65 |
| Tensile strength, Grade 450 | 450–585 MPa | SI; same public Scope. Inch-pound and SI values are independent, not exact conversions |
| Minimum yield strength | 35 ksi | Inch-pound; SSAB Grade 65 required properties as used on the official ASTM A516 Grade 65 and ASME SA516 Grade 65 pages. 35 ksi is not published here as 240 MPa or as an official SI specification value |
| Minimum elongation, 2 in. [50 mm] / 8 in. [200 mm] | 23% / 19% | SSAB required properties as used on the official pages, with A20/A20M or SA-20 thickness adjustments |
The 35 ksi yield minimum is a required-property figure from the SSAB Grade 65 datasheet as used on the official pages, not a typical heat result and not an official SI value. Do not treat 35 ksi as 240 MPa for an SI order. Elongation percentages (23% and 19%) are gauge-length minima, not thickness bands; A20/A20M or SA-20 adjustments still apply. Normalizing does not rewrite the tensile range. Allowable design stress is not published in A516 or SA-516; for many ASME VIII-1 designs, use the applicable II-D table for the SA-516 Grade 65 line.
ASME SA516 Grade 60 and ASTM A516 Grade 70 are different strength grades, not Grade 65 values.
Frequently Asked Questions (FAQ)
What is the yield strength of ASME SA516 Grade 65?
The official public-reference minimum yield used on ASME SA516 Grade 65 is 35 ksi, from SSAB’s Grade 65 required properties. It is a minimum, not a typical value, and is not published here as 240 MPa.
What is the tensile strength of ASME SA516 Grade 65?
The A516/A516M-25 public Scope, as used on the official family pages, gives 65–85 ksi for Grade 65 and 450–585 MPa for Grade 450. The two unit systems are independent.
Does normalizing change the mechanical properties of ASME SA516 Grade 65?
Normalizing is a delivery condition. It does not replace the Grade 65 tensile and yield table with a different specified range.
Where are the official ASME SA516 Grade 65 mechanical properties published on this site?
On ASME SA516 Grade 65 and ASTM A516 Grade 65.
For plate to ASTM A516/A516M Grade 65 [Grade 450] or ASME SA-516 Grade 65, please contact Gangsteel with the designation, edition, unit system, delivery condition, dimensions, quantity and any supplementary requirements. Learn more about our pressure-vessel and boiler steel plate at Gangsteel.
