Gangsteel produces and exports EN 10025-6 S890QL quenched and tempered structural steel plate. S890QL is an ultra-high-strength grade in the EN 10025-6 steel plate family, with a minimum yield strength of 890 MPa for thicknesses up to 50 mm. It is used in cranes, lifting equipment, heavy vehicles and machinery where high load and low weight are both required.

S890QL is delivered in the quenched and tempered condition and has guaranteed Charpy impact energy at –40 °C, which makes it suitable for outdoor and cold-climate structures.

Grade Designation

  • S – Structural steel
  • 890 – Minimum yield strength 890 MPa (thickness ≤ 50 mm)
  • Q – Quenched and tempered delivery condition
  • L – Guaranteed Charpy V-notch impact energy at –40 °C

Steel number: 1.8983

Key Advantages of S890QL Steel Plate

  • Minimum yield strength of 890 MPa allows a large weight saving compared with S690 grades
  • Guaranteed impact toughness at –40 °C
  • Fine-grained quenched and tempered microstructure
  • Weldable with a controlled, qualified welding procedure
  • Lower maximum phosphorus and sulfur than S890Q

Chemical Composition (Heat Analysis, Maximum %)

Element C Si Mn P S N B Cr Cu Mo Nb Ni Ti V Zr
S890QL 0.20 0.80 1.70 0.020 0.010 0.015 0.005 1.50 0.50 0.70 0.06 2.0 0.05 0.12 0.15

Note: The steel is fully killed and fine-grained. The producing mill chooses the actual alloy content within these limits, and the carbon equivalent (CEV) for each heat is shown on the mill certificate.

Mechanical Properties

Thickness (mm) Yield Strength ReH min (MPa) Tensile Strength Rm (MPa) Elongation A min (%)
3 – 50 890 940 – 1100 11
> 50 – 100 830 880 – 1100 11
> 100 – 125 830 880 – 1100 11
Impact Test (Charpy V-notch) 0 °C –20 °C –40 °C
Longitudinal, KV min (J) 50 40 30
Transverse, KV min (J), if agreed 35 30 27

Note: Values follow EN 10025-6. The > 100 – 125 mm row is from the current edition (EN 10025-6:2019); the earlier 2004+A1 edition specified S890 grades only up to 100 mm, so state the edition on your order. Guaranteed values must be confirmed on the mill certificate.

Available Dimensions

  • Thickness: to enquiry, within the EN 10025-6 range for S890 grades
  • Width and length: to enquiry
  • Tolerances: EN 10029 unless otherwise agreed
  • Delivery condition: Quenched and Tempered (Q+T)

Main Applications

  • Mobile and crawler crane booms and structural parts
  • Lifting equipment and lifting beams
  • Concrete pump booms
  • Heavy transport trailers and chassis frames
  • Mining and construction machinery frames

Equivalent Grades of S890QL

Manufacturer / Standard Equivalent Grade Steel Number / Designation Remarks
EN 10025-6 S890QL 1.8983 Official European standard grade
EN 10137-2 (withdrawn) S890QL 1.8983 Former European standard, replaced by EN 10025-6
GB/T 16270 (China) Q890E – Approximate: similar strength class, impact tested at –40 °C; not identical limits
SSAB Strenx 900 (formerly Weldox 900) – Commercial brand, approximate; check the brand’s toughness class against S890QL
Dillinger DILLIMAX 890 – Commercial brand, approximate; not an EN designation
thyssenkrupp XABO 890 – Commercial brand, approximate; not an EN designation

Commercial brands are listed for reference only. They are not Gangsteel products and are not direct substitutes unless the project specification accepts them.

Related Products

Other grades in the EN 10025-6 steel plate range:

Frequently Asked Questions (FAQ)

What is the difference between S890Q, S890QL and S890QL1?

All three have the same strength. They differ in impact test temperature: S890Q at –20 °C, S890QL at –40 °C and S890QL1 at –60 °C. QL and QL1 also have lower maximum phosphorus and sulfur than Q.

What is the carbon equivalent (CEV) of S890QL?

EN 10025-6:2019 sets maximum CEV values that rise with thickness, starting at 0.72 for plates up to 50 mm. The actual CEV of each heat is lower or equal and is printed on the mill certificate. Use that value when you plan welding.

Is S890QL easy to weld?

S890QL can be welded, but it needs more care than lower-strength structural steels, and the risk of cold cracking increases with thickness. Use a qualified welding procedure (WPS) following EN 1011-2, low-hydrogen consumables and controlled heat input.

Does the yield strength drop for thicker plates?

Yes. The minimum yield strength is 890 MPa up to 50 mm and 830 MPa above 50 mm. Design to the value for the actual thickness and check it on the mill certificate.

Is S890QL the same as Strenx 900 or Weldox 900?

They are in the same strength class, but they are not identical. Strenx 900 (formerly Weldox 900) is an SSAB brand made to SSAB’s own data sheet. Whether S890QL can replace it depends on your drawing or project specification.

Can S890QL be cold formed?

Yes, but it needs larger bending radii and more press force than lower-strength steels. Hot forming is not recommended because it can destroy the quenched and tempered properties. Confirm forming limits for your thickness with the mill.

Should I choose S890QL or S960QL?

S960QL gives a higher yield strength and may allow thinner plate, but welding and forming are more demanding. S890QL is often chosen as a balance between strength and fabrication.

What information should I give when asking for a quotation?

Give the grade (EN 10025-6 S890QL), the standard edition, plate thickness, width, length, quantity, any extra tests (for example transverse impact or ultrasonic testing) and the inspection certificate type you need.

For a quotation or technical data for EN 10025-6 S890QL steel plate, please contact Gangsteel.

EN10025-6 S890QL quenched and tempered steel plate Supplier