Gangsteel produces and exports EN 10025-6 S690Q quenched and tempered structural steel plate. S690Q belongs to the most widely used high-strength level of the EN 10025-6 steel plate family, with a minimum yield strength of 690 MPa for thicknesses up to 50 mm. It is used where a welded structure must carry high loads with less steel weight than ordinary structural grades.
S690Q is delivered in the quenched and tempered condition and is Charpy impact tested at –20 °C. For colder service, the same strength level is available as S690QL (–40 °C) and S690QL1 (–60 °C).
Grade Designation
- S – Structural steel
- 690 – Minimum yield strength 690 MPa (thickness ≤ 50 mm)
- Q – Quenched and tempered delivery condition, with impact energy guaranteed down to –20 °C
Steel number: 1.8931
Key Advantages of S690Q Steel Plate
- Minimum yield strength of 690 MPa, about twice that of common S355 structural steel
- Guaranteed impact toughness at –20 °C
- Fine-grained quenched and tempered microstructure
- Weldable with a qualified welding procedure
- Specified over a wide thickness range in EN 10025-6
Chemical Composition (Heat Analysis, Maximum %)
| Element | C | Si | Mn | P | S | N | B | Cr | Cu | Mo | Nb | Ni | Ti | V | Zr |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| S690Q | 0.20 | 0.80 | 1.70 | 0.025 | 0.015 | 0.015 | 0.005 | 1.50 | 0.50 | 0.70 | 0.06 | 2.0 | 0.05 | 0.12 | 0.15 |
Note: The steel is fully killed and fine-grained. The producing mill chooses the actual alloy content within these limits, and the carbon equivalent (CEV) for each heat is shown on the mill certificate.
Mechanical Properties
| Thickness (mm) | Yield Strength ReH min (MPa) | Tensile Strength Rm (MPa) | Elongation A min (%) |
|---|---|---|---|
| 3 – 50 | 690 | 770 – 940 | 14 |
| > 50 – 100 | 650 | 760 – 930 | 14 |
| > 100 – 150 | 630 | 710 – 900 | 14 |
| Impact Test (Charpy V-notch) | 0 °C | –20 °C |
|---|---|---|
| Longitudinal, KV min (J) | 40 | 30 |
| Transverse, KV min (J), if agreed | 30 | 27 |
Note: Values follow EN 10025-6 (thickness rows as in the 2004+A1 edition; the 2019 edition extends S690 grades to 200 mm). Guaranteed values depend on thickness and the standard edition ordered, and must be confirmed on the mill certificate.
Available Dimensions
- Thickness: to enquiry, within the EN 10025-6 range for S690 grades (from 3 mm; up to 150 mm in the 2004+A1 edition and 200 mm in the 2019 edition)
- Width and length: to enquiry
- Tolerances: EN 10029 unless otherwise agreed
- Delivery condition: Quenched and Tempered (Q+T)
Main Applications
- Mobile crane booms, outriggers and chassis
- Heavy trailers, truck frames and tipper bodies
- Mining equipment and hydraulic roof supports
- Excavator, loader and other construction machinery parts
- Bridges, offshore and other high-load welded structures
Equivalent Grades of S690Q
| Manufacturer / Standard | Equivalent Grade | Steel Number / Designation | Remarks |
|---|---|---|---|
| EN 10025-6 | S690Q | 1.8931 | Official European standard grade |
| EN 10137-2 (withdrawn) | S690Q | 1.8931 | Former European standard, replaced by EN 10025-6 |
| EN 10025-6 | S690QL | 1.8928 | Same strength, tested at –40 °C; can replace S690Q, not the reverse |
| GB/T 16270 (China) | Q690D | – | Approximate: similar strength class, impact tested at –20 °C; not identical limits |
| ASTM | A514 / A517 | – | Partial equivalent only: similar yield strength, different chemistry, impact and thickness rules |
| SSAB | Strenx 700 (formerly Weldox 700) | – | Commercial brand, approximate; check the brand’s toughness class against S690Q |
| Dillinger | DILLIMAX 690 | – | Commercial brand, approximate; not an EN designation |
| thyssenkrupp | N-A-XTRA 700 | – | Commercial brand, approximate; not an EN designation |
Commercial brands are listed for reference only. They are not Gangsteel products and are not direct substitutes unless the project specification accepts them.
Related Products
Other grades in the EN 10025-6 steel plate range:
- EN 10025-6 S690QL steel plate
- EN 10025-6 S690QL1 steel plate
- EN 10025-6 S620Q steel plate
- EN 10025-6 S890Q steel plate
- Low alloy and high strength steel plate
Frequently Asked Questions (FAQ)
What is the difference between S690Q, S690QL and S690QL1?
All three have the same strength. They differ in impact test temperature: S690Q at –20 °C, S690QL at –40 °C and S690QL1 at –60 °C. QL and QL1 also have lower maximum phosphorus and sulfur than Q.
What is the carbon equivalent (CEV) of S690Q?
EN 10025-6:2019 sets maximum CEV values that rise with thickness, from 0.65 for plates up to 50 mm to 0.83 for the thickest plates. The actual CEV of each heat is printed on the mill certificate. Use that value when you plan welding.
Is S690Q weldable?
Yes. S690Q is a weldable fine-grained steel, but it needs a qualified welding procedure (WPS) following EN 1011-2, low-hydrogen consumables and controlled heat input. The cold cracking risk increases with plate thickness.
Does the yield strength drop for thicker plates?
Yes. The minimum yield strength is 690 MPa up to 50 mm, 650 MPa above 50 mm to 100 mm, and 630 MPa for thicker plates. Design to the value for the actual thickness and check it on the mill certificate.
Is S690Q the same as Strenx 700 or Weldox 700?
They are in the same strength class, but they are not identical. Strenx 700 (formerly Weldox 700) is an SSAB brand made to SSAB’s own data sheet. Whether S690Q can replace it depends on the toughness level and approval required by your drawing or specification.
Is S690Q equivalent to ASTM A514?
Only partly. Both are quenched and tempered steels with similar yield strength, but chemistry, impact testing and thickness rules are different. Do not substitute one for the other without the designer’s approval.
Can S690Q be cold formed?
Yes, but it needs larger bending radii than ordinary structural steel, and more press force. Hot forming is not recommended because it can destroy the quenched and tempered properties. Confirm forming limits for your thickness with the mill.
What information should I give when asking for a quotation?
Give the grade (EN 10025-6 S690Q), the standard edition, plate thickness, width, length, quantity, any extra tests (for example transverse impact or ultrasonic testing) and the inspection certificate type you need.
For a quotation or technical data for EN 10025-6 S690Q steel plate, please contact Gangsteel.
