Gangsteel produces and exports EN 10025-6 S690QL1 quenched and tempered structural steel plate. S690QL1 belongs to the most widely used high-strength level of the EN 10025-6 steel plate family, with a minimum yield strength of 690 MPa for thicknesses up to 50 mm. It is used where a welded structure must carry high loads with less steel weight than ordinary structural grades.

S690QL1 is delivered in the quenched and tempered condition and has guaranteed Charpy impact energy at –60 °C, the lowest test temperature in EN 10025-6. It is the choice for arctic, offshore and other very low-temperature service where S690QL (–40 °C) is not enough.

Grade Designation

  • S – Structural steel
  • 690 – Minimum yield strength 690 MPa (thickness ≤ 50 mm)
  • Q – Quenched and tempered delivery condition
  • L1 – Guaranteed Charpy V-notch impact energy at –60 °C

Steel number: 1.8988

Key Advantages of S690QL1 Steel Plate

  • Minimum yield strength of 690 MPa, about twice that of common S355 structural steel
  • Guaranteed impact toughness at –60 °C
  • Fine-grained quenched and tempered microstructure
  • Weldable with a qualified welding procedure
  • Specified over a wide thickness range in EN 10025-6

Chemical Composition (Heat Analysis, Maximum %)

Element C Si Mn P S N B Cr Cu Mo Nb Ni Ti V Zr
S690QL1 0.20 0.80 1.70 0.020 0.010 0.015 0.005 1.50 0.50 0.70 0.06 2.0 0.05 0.12 0.15

Note: The steel is fully killed and fine-grained. The producing mill chooses the actual alloy content within these limits, and the carbon equivalent (CEV) for each heat is shown on the mill certificate.

Mechanical Properties

Thickness (mm) Yield Strength ReH min (MPa) Tensile Strength Rm (MPa) Elongation A min (%)
3 – 50 690 770 – 940 14
> 50 – 100 650 760 – 930 14
> 100 – 150 630 710 – 900 14
Impact Test (Charpy V-notch) 0 °C –20 °C –40 °C –60 °C
Longitudinal, KV min (J) 60 50 40 30
Transverse, KV min (J), if agreed 40 35 30 27

Note: Values follow EN 10025-6 (thickness rows as in the 2004+A1 edition; the 2019 edition extends S690 grades to 200 mm). Guaranteed values depend on thickness and the standard edition ordered, and must be confirmed on the mill certificate.

Available Dimensions

  • Thickness: to enquiry, within the EN 10025-6 range for S690 grades (from 3 mm; up to 150 mm in the 2004+A1 edition and 200 mm in the 2019 edition)
  • Width and length: to enquiry
  • Tolerances: EN 10029 unless otherwise agreed
  • Delivery condition: Quenched and Tempered (Q+T)

Main Applications

  • Mobile crane booms, outriggers and chassis
  • Heavy trailers, truck frames and tipper bodies
  • Mining equipment and hydraulic roof supports
  • Excavator, loader and other construction machinery parts
  • Bridges, offshore and other high-load welded structures

Equivalent Grades of S690QL1

Manufacturer / Standard Equivalent Grade Steel Number / Designation Remarks
EN 10025-6 S690QL1 1.8988 Official European standard grade
EN 10137-2 (withdrawn) S690QL1 1.8988 Former European standard, replaced by EN 10025-6
GB/T 16270 (China) Q690F – Approximate: similar strength class, impact tested at –60 °C; not identical limits
SSAB Strenx 700 (formerly Weldox 700) – Commercial brand, approximate; check the brand’s toughness class against S690QL1
Dillinger DILLIMAX 690 – Commercial brand, approximate; not an EN designation
thyssenkrupp N-A-XTRA 700 – Commercial brand, approximate; not an EN designation

Commercial brands are listed for reference only. They are not Gangsteel products and are not direct substitutes unless the project specification accepts them.

Related Products

Other grades in the EN 10025-6 steel plate range:

Frequently Asked Questions (FAQ)

What is the difference between S690Q, S690QL and S690QL1?

All three have the same strength. They differ in impact test temperature: S690Q at –20 °C, S690QL at –40 °C and S690QL1 at –60 °C. QL and QL1 also have lower maximum phosphorus and sulfur than Q.

What is the carbon equivalent (CEV) of S690QL1?

EN 10025-6:2019 sets maximum CEV values that rise with thickness, from 0.65 for plates up to 50 mm to 0.83 for the thickest plates. The actual CEV of each heat is printed on the mill certificate. Use that value when you plan welding.

Is S690QL1 weldable?

Yes. S690QL1 is a weldable fine-grained steel, but it needs a qualified welding procedure (WPS) following EN 1011-2, low-hydrogen consumables and controlled heat input. The cold cracking risk increases with plate thickness.

Does the yield strength drop for thicker plates?

Yes. The minimum yield strength is 690 MPa up to 50 mm, 650 MPa above 50 mm to 100 mm, and 630 MPa for thicker plates. Design to the value for the actual thickness and check it on the mill certificate.

Is S690QL1 the same as Strenx 700 or Weldox 700?

They are in the same strength class, but they are not identical. Strenx 700 (formerly Weldox 700) is an SSAB brand made to SSAB’s own data sheet. Whether S690QL1 can replace it depends on the toughness level and approval required by your drawing or specification.

Should I choose S690QL1 or S890QL1?

S890QL1 gives a much higher yield strength and may allow thinner plate, but welding and forming are more demanding. S690QL1 is often chosen as a balance between strength and fabrication. The designer should approve any change of grade.

Can S690QL1 be cold formed?

Yes, but it needs larger bending radii than ordinary structural steel, and more press force. Hot forming is not recommended because it can destroy the quenched and tempered properties. Confirm forming limits for your thickness with the mill.

What information should I give when asking for a quotation?

Give the grade (EN 10025-6 S690QL1), the standard edition, plate thickness, width, length, quantity, any extra tests (for example transverse impact or ultrasonic testing) and the inspection certificate type you need.

For a quotation or technical data for EN 10025-6 S690QL1 steel plate, please contact Gangsteel.

EN10025-6 S690QL1 quenched and tempered steel plate Supplier