ASTM A285 Grade C pressure-vessel plate   Match the ordered edition’s steelmaking and strength basis to the actual analysis records, delivered condition and vessel requirements.

Use the current Scope for a fusion-welded pressure-vessel enquiry

ASTM A285/A285M Grade C is carbon steel plate in a low- and intermediate-tensile-strength specification for fusion-welded pressure vessels. The A285/A285M-24 official public Scope permits killed or semi-killed steel at the producer’s option. Grade C remains current alongside Grades A and B and has the highest specified tensile range within that family. This is a vessel-plate requirement, not a structural-weathering designation.

A Gangsteel enquiry should identify A285/A285M Grade C, the required edition, dimensions, quantities and purchasing units. The supplier material line must also be compatible with the vessel design and project acceptance basis. Scope compliance is not by itself approval of a completed vessel, a fabrication process or a substitute grade.

A285 Grade C Scope and delivery decisions
Item Current basis Purchasing implication
Steelmaking practice Scope 1.1: killed or semi-killed Identify any project requirement for killed steel only
Maximum plate thickness Scope 1.3: composition must meet specified mechanical properties No fixed official 50 mm or 2 in. cap is stated there
Usual delivery Official store abstract: normally as-rolled Specify any required treatment; no mandatory normalizing inferred
Coil-derived plate Scope 1.4: conditional additional A20 requirements Identify route, treatment and applicable testing/reporting
Units Inch-pound and SI are independent standard systems Do not combine rounded values from different systems

Thickness is composition-limited, not a universal 50-mm cutoff

Scope 1.3 limits maximum thickness by the capacity of the composition to meet the specified mechanical properties. It does not establish a fixed 50 mm or 2 in. official upper limit. SSAB’s Grade C datasheet dated 19 April 2017 lists mill plate from 0.1875 to 2.00 in.; that is a producer range, not the current specification’s cap or a Gangsteel availability statement. A requested thickness still needs technical and supply review; removal of a fixed cap is not unlimited coverage or a capacity guarantee.

Some commercial introductions retain older internal-soundness and broader steelmaking wording. The official store abstract itself contains broader deoxidation wording than Scope 1.1. The basis used here follows the 24 edition’s Scope for steelmaking and thickness, rather than those older summaries. Trader supply-range statements likewise do not create specification limits.

The store abstract says plate is normally supplied as-rolled. Neither that usual condition nor the public Scope establishes mandatory normalizing, stress relief or a default postweld heat treatment. Define any required heat-treatment condition under the applicable order and fabrication basis. Distinguish the condition represented by material tests from any treatment subsequently required by the vessel project.

Keep heat and product manganese separate in the reference chemistry

The table summarizes public compilation references, not an official chemistry-table extract. Octal’s Grade C table, reviewed on 11 November 2026, distinguishes heat and product Mn. Ferrobend instead prints a single 0.98% Mn entry and states that its table applies to both analyses. That difference is disclosed rather than resolved into an invented official column. C/P/S references agree across the two compilations; silicon is not printed in their tables and receives no numerical limit here.

A285 Grade C chemistry — compilation references, mass %, with unresolved Mn basis
Element Heat reference, max % Product reference, max % Source limitation
Carbon (C) 0.28 0.28 C applies to both analyses in the cited compilations
Manganese (Mn) 0.90 0.98 Octal split; Ferrobend prints only 0.98 for both analyses
Phosphorus (P) 0.025 0.025 Compilation values; confirm the ordered-edition requirements
Sulfur (S) 0.025 0.025 Compilation values; confirm the ordered-edition requirements
Silicon (Si) Not printed in the checked tables; no numerical limit assigned

The Octal heat maximum is not cancelled by Ferrobend’s combined entry. Conversely, the existence of a two-column compilation does not turn either source into an inspected official table. Obtain the applicable chemical requirements and analysis basis for the ordered edition, then compare the actual material records. Keep the heat identity and any product-analysis identification connected to the plate under review.

The phosphorus/sulfur figures above are qualified public references, not a claim that a paid current official table has been reproduced or that no stricter project condition can apply. Unprinted elements should not be completed from a neighboring pressure-vessel grade. A full material designation and a legible report are more useful to acceptance review than an unlabelled row of percentages.

Separate the official tensile range from mill-reference minima

A285 Grade C mechanical requirements — official Scope and public references distinguished
Property Grade C value Evidence basis
Tensile strength 55–75 ksi [380–515 MPa] Official A285/A285M-24 public Scope 1.2
Yield strength, minimum 30 ksi [205 MPa] SSAB, Ferrobend and Octal public references
Elongation, minimum 23% in 8 in. [200 mm] Public reference; applicable A20 adjustments
Elongation, minimum 27% in 2 in. [50 mm] Public reference; applicable A20 adjustments

The tensile range is directly in official public Scope 1.2, rather than merely a distributor restatement. The yield and elongation entries are public references supported by SSAB’s 2017 datasheet and the two compilations. Retain both elongation gauges and assess applicable A20 adjustments before comparing a result. A percentage detached from its specimen basis is not a complete inspection comparison.

For plate produced from coil and furnished without heat treatment or with stress relieving only, Scope 1.4 applies additional A20/A20M requirements, including tests and reporting of additional results. Confirm the proposed route and documentary coverage instead of assuming every product origin has identical acceptance paperwork. The public references do not make Charpy impact testing a basic requirement; where the project needs notch toughness, agree the applicable test and acceptance conditions explicitly.

A killed-steel pointer is not permission to substitute another specification

Scope Note 1 directs buyers requiring killed carbon steel only to A299/A299M, A515/A515M or A516/A516M. That direction is not interchangeability. A516 Grade 70 plate addresses a different vessel-material basis for moderate- and lower-temperature service; A515 Grade 70 plate is a different intermediate- and higher-temperature-service specification. These links provide purpose contrasts, not A285 chemical or numerical evidence.

Compare the complete vessel design requirements, required toughness, steelmaking condition, treatment and documentary acceptance before any alternative is approved. Similar tensile terminology is insufficient. No default certificate type, welding procedure, stock position, manufacturing capacity or delivery period follows from this page. Define required examinations rather than infer an unverified supplementary-requirement menu.

A285 Grade C purchasing questions

Is there a fixed official 50-mm maximum, and what steelmaking practice applies?

The 24 edition’s public Scope limits thickness by composition’s ability to meet mechanical properties, not a fixed 50 mm cap. Scope 1.1 permits killed or semi-killed steel. Older commercial summaries do not override those provisions; a producer’s listed range is a separate matter.

What strength and elongation basis should be used, and is normalizing compulsory?

Official Scope gives tensile strength of 55–75 ksi [380–515 MPa]. Public references give 30 ksi [205 MPa] minimum yield, 23% in 8 in. and 27% in 2 in., subject to applicable A20 adjustments. Plate is normally as-rolled; no base mandatory normalizing is established here.

May Grade C replace A516 Grade 70 or A515 Grade 70 directly?

No automatic replacement is established. The killed-steel pointer in Scope Note 1 is not substitution permission. Review the vessel design code, intended service, toughness requirements and project approval before accepting an alternative.

Why are manganese heat and product entries not collapsed into one limit?

Octal prints 0.90% heat and 0.98% product, while Ferrobend prints one 0.98% value with a both-analyses note. The conflict remains a source limitation. Confirm the ordered-edition analysis requirements instead of declaring one compilation column official.

Can coil-derived plate use the same inspection assumptions without review?

No. Scope 1.4 identifies additional A20 testing and reporting for coil-derived plate furnished without heat treatment or with stress relieving only. Establish the route, delivered condition and applicable records before accepting the inspection package.

Prepare an A285 Grade C enquiry

Give Gangsteel the complete vessel-plate requirement for review.

  • Edition, unit system, dimensions and quantities
  • Steelmaking or treatment requirements and proposed product route
  • Analysis basis, test scope, any toughness criteria and certificate requirements

Any availability, alternative-material or documentary commitment must be confirmed for the specific order. Contact Gangsteel with the applicable material requirements.

ASTM A285GR.C and A285 Grade C steel plate Supplier