ASTM A516 Grade 65, also commonly written as A516GR.65, A516 Gr.65, A516 GR 65 and ASTM A516/A516M Grade 65 [Grade 450], is the inch-pound Grade 65 designation in ASTM A516/A516M. Grade 450 is the SI designation in the same specification, not a converted Grade 65 value. ASME SA516 Grade 65 (SA-516 or SA-516M Grade 65 or Grade 450) is the corresponding ASME family designation, not merely another spelling of the ASTM name. An ASTM-only certificate does not automatically satisfy a specified SA-516 order, and the reverse is also true. The official product page is ASTM A516 Grade 65.
This datasheet restates the official public-reference values already disclosed on ASTM A516 Grade 65 and ASME SA516 Grade 65 for chemistry, tensile properties and the usual delivery-condition pattern. It is a procurement-oriented summary, not a certified extract of the current ASTM or ASME edition and not a mill test certificate.
Identification
| Item | Public-reference statement |
|---|---|
| Specification and grade | ASTM A516/A516M Grade 65 (inch-pound) or Grade 450 (SI). ASME SA516 Grade 65 is the corresponding ASME designation |
| Product and service | Killed, fine-grain carbon-manganese plate for welded pressure vessels in moderate and lower-temperature service where notch toughness matters |
| General requirements | A20/A20M, or SA-20 when the order is written to the ASME designation |
| Related grades | ASTM A516 Grade 60 and ASTM A516 Grade 70 are different strength grades in the same specification, not replacements |
Chemical Composition and Mechanical Properties
Carbon maxima, heat = product: 0.24% at ½ in. [12.5 mm] and under; 0.26% over ½ in. to 2 in.; 0.28% over 2 in. to 4 in.; 0.29% over 4 in. Manganese is 0.85–1.20% heat and 0.79–1.30% product in both Grade 65 thickness bands. Silicon is 0.15–0.40% heat and 0.13–0.45% product. Phosphorus and sulfur are 0.025 or 0.035 in public references; use the ordered edition. A carbon–manganese adjustment permits 0.06% Mn above the specified maximum for each 0.01% C below the specified carbon maximum, up to 1.50% heat / 1.60% product.
| Property | Published reference value | Basis / conditions |
|---|---|---|
| Tensile strength, Grade 65 | 65–85 ksi | Inch-pound; ASTM A516/A516M-25 public Scope |
| Tensile strength, Grade 450 | 450–585 MPa | SI; ASTM A516/A516M-25 public Scope. Inch-pound and SI values are independent, not exact conversions |
| Minimum yield strength | 35 ksi | Inch-pound; SSAB Grade 65 published required properties, as disclosed on the official ASTM A516 Grade 65 and ASME SA516 Grade 65 pages, and consistent with Ferrobend, MetalMate and PipingMart compilations. 35 ksi is not published here as 240 MPa or as an official SI specification value |
| Minimum elongation, 2 in. [50 mm] gauge | 23% | SSAB required properties as used on the official grade page; thickness adjustments per A20/A20M or the corresponding ordered SA-20 requirements |
| Minimum elongation, 8 in. [200 mm] gauge | 19% | Same reference basis and applicable thickness adjustments |
Delivery Condition and Supplementary Tests
Public compilations and the SSAB Grade 65 datasheet, as used on the official pages, state that plates over 1.50 in. [40 mm] are supplied normalized unless otherwise ordered, and that plates 1.50 in. and under are normally as-rolled unless otherwise agreed or unless notch toughness is specified, in which case normalizing is the usual condition unless the purchaser specifies otherwise. Charpy testing, HIC/NACE testing and a hardness acceptance value are not automatic Grade 65 requirements; write them on the order if the project needs them.
Frequently Asked Questions (FAQ)
Is this datasheet a substitute for the official ASTM A516 Grade 65 product page?
No. It is a summary of the public-reference figures already published on ASTM A516 Grade 65 and ASME SA516 Grade 65. The official pages and the ordered edition govern acceptance.
What tensile strength is listed for ASTM A516 Grade 65 on this datasheet?
65–85 ksi for Grade 65 and 450–585 MPa for Grade 450, from the ASTM A516/A516M-25 public Scope. The two unit systems are independent.
Does this ASTM A516 Grade 65 datasheet include a default impact test?
No. Impact testing is supplementary and must be ordered if required.
How should an enquiry for ASTM A516 Grade 65 be written?
Name the designation, edition, unit system, delivery condition, dimensions, quantity and any supplementary requirements, and contact Gangsteel.
For plate to ASTM A516/A516M Grade 65 [Grade 450] or ASME SA-516 Grade 65, please contact Gangsteel with the designation, edition, unit system, delivery condition, dimensions, quantity and any supplementary requirements. Learn more about our pressure-vessel and boiler steel plate at Gangsteel.
