SA-515 Grade 65: compare offers on the same test basis

An SA515 Grade 65 quotation is only useful when the proposed plate condition, test results and ASME acceptance basis are comparable. Gangsteel invites project enquiries that identify the exact Grade 65 requirement rather than a general request for stronger boiler plate. A nominal tensile class alone cannot resolve delivery condition, specimen requirements or certification for a pressure-vessel order.

Read the strength requirement before judging an alternative

For preliminary screening, the ASTM A515/A515M-17(2022) official public Scope gives the Grade 65 tensile range below. Yield and elongation are public references supported by MetalMate’s grade-specific guide, the Ferrobend family table and the H62 mill reference where covered. These are ASTM-family figures, not an official SA-515 extract for a named Code year; the order’s ASME requirements must be checked independently.

Grade 65 offer-screening mechanical reference
Reported characteristic Family reference Comparison discipline
Tensile strength 65–85 ksi [450–585 MPa] Check both lower and upper limits
Yield strength, minimum 35 ksi [240 MPa] Do not substitute the tensile lower bound
Elongation, 8 in. [200 mm] gauge 19% Identify specimen geometry and applicable adjustments
Elongation, 2 in. [50 mm] gauge 23% Compare like gauge lengths, not thickness bands

The SI family name Grade 450 comes from tensile strength, not a 450 MPa yield requirement. A test report must distinguish measured yield, measured tensile strength and elongation. A result above the minimum yield does not remove the upper tensile limit or other requirements. Applicable A20 elongation adjustments and specimen rules must be considered; listing both gauges is not a claim that every plate requires two different elongation tests.

This carbon-silicon family is intended for intermediate- and higher-temperature welded-boiler and pressure-vessel service. The official ASTM abstract describes killed steel and coarse austenitic grain practice. Room-temperature strength figures do not establish allowable stress at the vessel’s operating temperature, nor do they demonstrate notch toughness. Keep design selection with the responsible engineer and the governing construction rules.

Use Grade 65 chemistry, not a neighbouring strength grade

Carbon limits change with thickness, while manganese has distinct heat and product bases. The following mass percentages are labelled public-reference chemistry from the Grade 65 guide and family compilation. H62 provides useful mill corroboration within its published range, not proof of every heavy-plate size. These data are neither actual heat results nor a current named-Code official table.

Grade 65 public-reference chemistry by analysis basis
Constituent and band Heat analysis Product analysis
Carbon, ≤1 in. [25 mm], max 0.28 0.28
Carbon, >1–2 in. [>25–50 mm], max 0.31 0.31
Carbon, >2–4 in. [>50–100 mm], max 0.33 0.33
Carbon, >4–8 in. [>100–200 mm], max 0.33 0.33
Carbon, >8 in. [>200 mm], max 0.33 0.33
Manganese, basic max 0.90 0.98
Silicon 0.15–0.40 0.13–0.45
Phosphorus, max 0.025 0.025
Sulfur, max 0.025 0.025

Read the carbon row that corresponds to the ordered thickness. The basic manganese maxima are 0.90% heat and 0.98% product, not Grade 70’s manganese limits. MetalMate and Ferrobend describe a carbon–manganese adjustment reaching 1.50% heat and 1.60% product: each 0.01 percentage-point carbon reduction allows 0.06 additional manganese. H62 omits that footnote, so confirm any proposed adjustment against the ordered edition rather than rejecting or accepting a heat from the basic line alone.

Keep phosphorus and sulfur at the stated public-reference basis and compare certified results to the approved requirements. A wider product-analysis silicon range is not the heat-analysis range. If the project imposes tighter residuals or a chemistry calculation, state the formula, analysis basis and limits explicitly; do not infer a universal welding limit from the grade table.

Make the ASME requirement an auditable purchase instruction

Specify SA-515 or SA-515M, Grade 65, the governing Code year or Section II-A edition, and the required unit system. An ASTM A515 Grade 65 certificate is not by itself SA-515 acceptance, and dual certification is not automatic. The historical ASME contents listing establishes the specification title only. BPVC.II.A-2025 has not been read here, and no current adoption year is asserted from that listing or an old designation suffix.

Grade 65 offer-to-order decision record
Decision Purchaser instruction Evidence to review
Edition and designation SA-515 or SA-515M, Grade 65; named Code year or Section II-A edition Material designation and applicable edition on accepted documents
Geometry and quantity Thickness, width, length, unit system, tolerances and piece schedule Dimensions and traceable plate identifiers
Condition and fabrication Required delivery condition; relevant subsequent thermal cycles Reported treatment and representative testing condition
Acceptance package Tests, acceptance criteria, certificate form and witness requirements Actual results with heat and plate linkage; agreed inspection records

Keep inch-pound and SI requirements independent. The bracketed values are separately standard, not exact mathematical equivalents to be mixed when checking compliance. Where a drawing and a requisition use different systems, resolve the controlling basis before comparing offers. Similarly, a change from Grade 60 to Grade 65 is a material revision for engineering approval, not a supplier’s automatic strength upgrade.

Separate mill delivery from later workshop treatment

As an ASTM-family compilation restatement, MetalMate describes plate over 50 mm [2 in.] as normalized and thinner plate as normally as-rolled unless treatment is ordered. This is not a verified paid SA-515 clause. Confirm the applicable SA wording and any purchaser condition before release; do not apply the A516 treatment rule to this family. “As-rolled and normalized” is not a satisfactory single description of the delivered plate.

Subsequent forming or fabrication heat treatment can change the relevance of original mill results. If the project requires testing after a simulated thermal cycle, provide the approved cycle and acceptance requirements before procurement. A normalized delivery report alone does not demonstrate performance after every possible workshop cycle, and a stress-relieved delivery description does not settle all fabrication-code obligations.

There is no fixed 300 mm specification maximum established by the former rolling-practice wording. The ASTM family relates maximum thickness to composition’s ability to meet mechanical requirements; actual size capability needs separate confirmation. Do not turn a mill’s quoted range into an ASME limit. Additional impact testing or ultrasonic examination must be defined when required, with criteria and coverage; neither is a default guarantee here.

Choose the correct specification route

The ASTM A515 Grade 65 supplier page addresses the ASTM counterpart rather than ASME acceptance. The ASME SA515 Grade 60 related topic is provided for family navigation, not as a numerical source or approved replacement. Keep any alternative proposal separate from the specified Grade 65 offer and identify the documents needing engineering review.

Questions when buying SA-515 Grade 65

Does the number 65 describe yield strength?

No. The family public reference is 65–85 ksi tensile and 35 ksi minimum yield. In SI terms, 450–585 MPa tensile and 240 MPa yield must not be confused with a 450 MPa yield claim.

Why might two elongation reports show different percentages?

First compare gauge length, specimen geometry and any permitted adjustment. The references are 19% in 8 in. [200 mm] and 23% in 2 in. [50 mm]. A percentage without that context is insufficient for acceptance.

Can a different vessel grade be accepted because its tensile range overlaps?

Not on strength overlap alone. Review chemistry, grain practice, condition, Code listing, toughness and certification. A proposed substitution needs the project’s approval, even where an individual tensile result looks suitable.

What is needed if fabrication includes a long thermal cycle?

Tell the supplier the approved cycle and whether representative testing after simulation is required. Establish specimen condition and acceptance criteria in advance; do not rely solely on tests made in the original delivery condition.

Which documents should be checked before cutting starts?

Check the approved order, material report, plate marking, dimensions, condition and required examination records. Resolve mismatched identifiers or missing results before processing, and define how identification will be maintained on cut pieces.

Request a Grade 65 offer with clear acceptance conditions

Provide the Code edition, SA designation, unit system, plate dimensions and quantity, delivery condition, tests and certificate form. Include any alternative-material proposal as a separate item so technical acceptance is not confused with price comparison.

Contact Gangsteel with your plate enquiry

ASME SA515GR65 and SA515 Grade 65 steel plate supplier