ASTM A516 Grade 65, also commonly written as A516GR.65, A516 Gr.65, A516 GR 65 and ASTM A516/A516M Grade 65 [Grade 450], is the inch-pound Grade 65 designation in ASTM A516/A516M. Grade 450 is the SI designation in the same specification, not a converted Grade 65 value. ASME SA516 Grade 65 (SA-516 or SA-516M Grade 65 or Grade 450) is the corresponding ASME family designation, not merely another spelling of the ASTM name. An ASTM-only certificate does not automatically satisfy a specified SA-516 order, and the reverse is also true. The official product page is ASTM A516 Grade 65.

This page compares ASTM A516 Grade 65 with ASTM A36/A36M carbon structural steel. A36 is written to ASTM A6/A6M general requirements for structural products, not to A20/A20M pressure-vessel-plate requirements. Gangsteel does not have an official A36 product page, so the A36 figures below are taken from public compilations of ASTM A36/A36M-19 for plate and are listed without a link. The comparison is not a substitution approval.

Pressure-Vessel Plate versus Carbon Structural Steel

Topic ASTM A516 Grade 65 ASTM A36 / A36M plate
Type of specification Pressure-vessel carbon-manganese plate for moderate and lower-temperature service where notch toughness matters, with ASME SA516 Grade 65 as the corresponding ASME designation Carbon structural steel for riveted, bolted or welded construction of bridges, buildings and general structural purposes
General requirements A20/A20M (or SA-20) A6/A6M
Notch toughness The specification is written for service where improved notch toughness is important; a Charpy test still has to be ordered if it is required Not a basic A36 requirement. Any impact test is a supplementary or project requirement

Chemical Composition of Plate

Element / thickness ASTM A516 Grade 65 [Grade 450], public reference A36/A36M-19 plate compilations
Carbon, max 0.24 / 0.26 / 0.28 / 0.29 / 0.29 at ½ in. and under / over ½ to 2 / over 2 to 4 / over 4 to 8 / over 8 in. (heat = product) 0.25% to 1½ in. [40 mm]; 0.26% over 1½ to 2½ in.; 0.27% over 2½ to 4 in.; 0.29% over 4 in.
Manganese 0.85–1.20% heat, 0.79–1.30% product, both Grade 65 thickness bands No specified range to ¾ in. [20 mm]; 0.80–1.20% over ¾ to 2½ in.; 0.85–1.20% over 2½ in. A carbon–manganese allowance to 1.35% Mn is compiled for reductions below the carbon maximum
Phosphorus / sulfur, max 0.025 or 0.035 each; see the official-page source note 0.030% P and 0.030% S for plate in these compilations
Silicon 0.15–0.40% heat, 0.13–0.45% product 0.40% max to 1½ in.; 0.15–0.40% over 1½ in.
Copper Not a single named official Grade 65 limit on the pages used here 0.20% min only when copper steel is specified

Mechanical Properties

Property ASTM A516 Grade 65 [Grade 450] A36/A36M-19 plate compilations
Tensile strength 65–85 ksi / 450–585 MPa, ASTM A516/A516M-25 public Scope 58–80 ksi [400–550 MPa] for plates, shapes and bars generally
Minimum yield strength 35 ksi, SSAB Grade 65 required properties as used on the official pages. 35 ksi is not published here as 240 MPa or as an official SI specification value 36 ksi [250 MPa] generally; compilations give 32 ksi [220 MPa] for plate over 8 in. [200 mm] thick
Minimum elongation, plates and bars 23% in 2 in. [50 mm] and 19% in 8 in. [200 mm], with A20/A20M or SA-20 adjustments 23% in 2 in. [50 mm] and 20% in 8 in. [200 mm], with A6/A6M adjustments (including a two-percentage-point reduction for plates wider than 24 in. [600 mm])

ASTM A516 Grade 60 and ASTM A516 Grade 70 are different A516 strength grades, not A36 equivalents. Substitutions require design and project approval.

Frequently Asked Questions (FAQ)

Can ASTM A36 replace ASTM A516 Grade 65?

Not without the project’s design and material approval. ASTM A36 is a structural specification. ASTM A516 Grade 65 is a pressure-vessel plate grade. This comparison is not a substitution approval.

Is ASTM A36 stronger than ASTM A516 Grade 65 because its general yield is 36 ksi?

The compiled A36 plate yield minimum is 36 ksi generally, against a 35 ksi Grade 65 minimum on the official pages. Tensile ranges differ, and the specifications, general-requirements basis and intended use still differ. A single yield figure is not permission to substitute ASTM A516 Grade 65.

Does ASTM A36 have the same toughness rules as ASTM A516 Grade 65?

No. A516 is written for moderate and lower-temperature vessel service where notch toughness matters, but a Charpy test is still ordered only when required. A36 does not, by itself, impose a Charpy test.

Where is the official product page after reading this ASTM A516 Grade 65 and A36 comparison?

Start with ASTM A516 Grade 65. Use ASME SA516 Grade 65 when the order is written to the ASME designation.

For plate to ASTM A516/A516M Grade 65 [Grade 450] or ASME SA-516 Grade 65, please contact Gangsteel with the designation, edition, unit system, delivery condition, dimensions, quantity and any supplementary requirements. Learn more about our pressure-vessel and boiler steel plate at Gangsteel.

A516 Grade 65 vs A36: Pressure-Vessel Plate vs Carbon Structural Steel