En 10250


material x30cr13

We have thousands tons stock of stainless steel sheet and coil with various size and grade,mainly include austenitic stainless steel, martens stainless steel (including precipitation hardened stainless steel sheet & coil), ferritic stainless steel, and duplex stainless steel.

Characteristics of Stainless Steel Sheet and Plate:
High corrosion resistance
High strength
High toughness and impact resistance
Temperature resistance
High workability, including machining, stamping, fabricating and welding
Smooth surface finish that can be easily clean

CPM REX T15 is an excellent high velocity steel made by the CPM process. CPM REX 121, is a brand new high vanadium cobalt bearing tool steel designed to supply a combination of the very best wear resistance, attainable hardness, and purple hardness obtainable in a high-pace steel.

It may be considered both a excessive hardness 440C stainless-steel or a corrosion-resistant D2 tool steel. 1.4028 is a stainless martensitic chromium steel. A higher carbon content is 1.4028 more hardenable than 1.4021. Good corrosion resistance in reasonably aggressive, chlorine-free media, natural acids, soaps and solvents.

440A is a relatively a low value, extremely corrosion resistant chrome steel. It may be very resistant to corrosion and is one of the most typical stainless alloys used for knife making. The once ubiquitous American Buck Model a hundred and ten Folding Hunter was made from 440C before 1981.

austenitic stainless-steel

  • Buck Knives and Gerber Knives use 420HC extensively.420A and 420B are economical, highly corrosion resistant chrome steel grades.
  • It obtains about fifty seven HRC after appropriate warmth therapy.
  • The HC stands for “high carbon” and it may be delivered to a higher hardness than common 420 and should not be mistaken for it.
  • 420 series contain a number of sorts with various carbon content material between .15% and .40% this steel grade is extensively used to make high finish razor blades, surgical scalpels etc.

Knife blades specified as being “440” can sometimes be assumed to be the lower hardness 440A grade. BG-42 Slightly greater in carbon, chrome and moly than ATS-34.

Most readily available W2 has a carbon content of not more than 1-1.1%. Bill Moran considered it to be almost as powerful as 5160, but it was unavailable for a time frame. W2 is among the carbon steels that may produce a pleasant Hamon in heat treating. Among wrought stainless steels, the composition of EN 1.4028 stainless-steel is notable for holding comparatively excessive amounts of chromium and manganese .

High strength, lower plasticity and weldability. Such as mechanical spring, blades of steam turbines, hydraulic press valves. Those steels are used after quenching and tempering and annealing after forging, impacting as nicely. The steels on this category have a lot greater resistance to components and corrosion than standard stainless steels. W2, a device steel that holds its edge quite nicely however not very powerful.

 

We produce ASTM/ASME Grade 304, Grade 304L,304h, 316, 316L, 316H, 316TI, 321, 321H, 309S, 309H, 310S, 310H, 410S, 2205, 904L, 2507, 254, gh3030, 625, 253MA, S30815, 317L, Type 317, 316lN, 8020, 800, 800H, C276, S32304 and others special requirement stainless steel grade.

Must be solid and heat handled at very high and actual temperatures. Can be used at very high hardness, such as RC sixty four-66. Not alleged to be brittle, however high alloy steels normally are. Although usually used for aerospace bearings and different crucial purposes, its wonderful wear resistance and corrosion resistance makes it a superior alternative to be used in cutlery purposes.

corrugated stainless-steel gasoline pipe

Sandvik series6C27, a typical knife steel grade with good corrosion resistance and low hardness, mainly used in applications where the need for put on resistance is low. Chinese-made steels which are similar to 440B however with a higher carbon, cobalt and vanadium content to add extra energy to the blade. Uses include excessive finish barber scissors, hunting knives and so forth. CPM S125V, online data isn’t available as of August 2014, contact Crucible Industries sales for information.

material
Tagged on: