410s Stainless Steel Properties

We produce ASTM/ASME Grade 304, Grade 304L,304h, 316, 316L, 316H, 316TI, 321, 321H, 309S, 309H, 310S, 310H, 410S, 2205, 904L, 2507, 254, gh3030, 625, 253MA, S30815, 317L, Type 317, 316lN, 8020, 800, 800H, C276, S32304 and others special requirement stainless steel grade.

Similar Alloys

Grade 410S stainless steel can be machined within the annealed situation though better results are obtained in heat treated and chilly drawn situations. The following datasheet provides an summary of grade 410S stainless steel. For each property being in contrast, the top bar is AISI 410 stainless-steel and the underside bar is AISI 410S stainless steel. The parts ought to then be immersed in a warm solution of 10-20% nitric acid followed by a water rinse to take away any residual iron. Scaling becomes extreme above 1500°F (811°C) in intermittent service.

These peaks had been attributed to the presence of precipitates with excessive chromium content of about 21%. In these FSW welds the sensitization of the AISI 410S steel was detected by the electrochemical check according to the intensity of the undesirable phases fashioned.

The DL-EPR take a look at was clearly in a position to quantify the totally different ranges of sensitization within the FSW welds based on the energy used by the process parameters. AISI 410S chrome steel is a martensitic stainless-steel formulated for main forming into wrought merchandise. Cited properties are appropriate for the annealed situation. The chemical composition of grade 410S stainless-steel is printed in the following desk.

 

• Among wrought stainless steels, the composition of AISI 410S chrome steel is notable for containing comparatively high amounts of chromium (Cr) and manganese (Mn).
• Manganese is used to improve ductility at elevated temperatures.
• Higher chromium content imparts additional corrosion resistance.
• Chromium is the defining alloying factor of chrome steel.

Stock Thickness: 0.1-200.0mm
Production thickness: 0.5.0-200mm
Width: 600-3900mm
Length: 1000-12000mm
Grade:
200 series: 201,202
300 series: 301,304,304L,304H,309,309S,310S,316L,316Ti,321,321H,330
400 series: 409,409l,410,420J1,420J2,430,436,439,440A/B/C
Duplex: 329,2205,2507,904L,2304
Surface: No.1,1D,2D,2B,NO.4/4K/hairline,satin,6k,BA,mirror/8K

If extreme massive grains are encountered after annealing mildly cold-worked material, the annealing temperature must be decreased to a range of 1200 – 1350°F (649 – 732°C) range. The oxidation resistance of those stainless-steel sheets is good and can be used for companies of temperature up to 1300 diploma F.

Higher chromium content imparts extra corrosion resistance. Manganese is used to improve ductility at elevated temperatures. It additionally permits a higher nitrogen content material than would in any other case be potential. Alloy 410S (UNS S41008) is a low carbon, non–hardening modification of Alloy 410 (UNS S41000) the general function 12% chromium martensitic chrome steel.

The low carbon and a small alloy addition reduce austenite formation at high temperatures which restricts the alloys capacity to harden. 410S remains delicate and ductile even when quickly cooled from above the crucial temperature. This non-hardening attribute helps forestall cracking when the alloy is uncovered to excessive temperatures or welded. It displays adequate corrosion resistance much like 410 and good oxidation resistance. AISI Type 410S is a non-hardenable, low carbon modification of Type 410, offering average strength with reasonable corrosion resistance.

Aisi 410s Applications

The following desk exhibits the bodily properties of grade 410S stainless steel. Stainless steels are excessive-alloy steels with good corrosion resistance due to large amounts of chromium current in them. It is annealed within the 1600 – 1650°F (871 – 899°C) range after which air cooled to alleviate cold working stresses. 410S shouldn’t be uncovered to temperatures of 2000°F (1093°C) or above because of embrittlement.

We have thousands tons stock of stainless steel sheet and coil with various size and grade,mainly include austenitic stainless steel, martens stainless steel (including precipitation hardened stainless steel sheet & coil), ferritic stainless steel, and duplex stainless steel.

Characteristics of Stainless Steel Sheet and Plate:
High corrosion resistance
High strength
High toughness and impact resistance
Temperature resistance
High workability, including machining, stamping, fabricating and welding
Smooth surface finish that can be easily clean