Alloy 310

We produce ASTM/ASME Grade 304, Grade 304L,304h, 316, 316L, 316H, 316TI, 321, 321H, 309S, 309H, 310S, 310H, 410S, 2205, 904L, 2507, 254, gh3030, 625, 253MA, S30815, 317L, Type 317, 316lN, 8020, 800, 800H, C276, S32304 and others special requirement stainless steel grade.

When heated between 1202 – 1742oF (650 – 950oC) the alloy is subject to sigma phase precipitation. A resolution annealing treatment at 2012 – 2102oF (1100 – 1150oC) will restore a level of toughness. The mechanical properties of grade 310 and grade 310S stainless steel are summarised in the following desk.

The high chromium and medium nickel content material make these steels succesful for applications in reducing sulphur atmospheres containing H2S. They are widely used in reasonably carburising atmospheres, as encountered in petrochemical environments. For extra extreme carburising atmospheres other heat resisting alloys must be chosen. Grade 310 isn’t recommended for frequent liquid quenching as it suffers from thermal shock. The grade is usually used in cryogenic purposes, because of its toughness and low magnetic permeability.

In connection with a worse thermal conductivity, a greater distortion must be expected. For product thicknesses over 12mm the double-V butt weld needs to be preferred as an alternative of a single-V butt weld. The included angle must be 60° – 70°, when utilizing MIG-welding about 50° is sufficient. The tacks must be subsequently grinded or a minimum of be free from crater cracks.

 

• This metal has an extensively higher coefficient of thermal enlargement as non-alloyed steels.
• Copper back-up plates for quicker warmth rejection are useful, whereas, to avoid cracks within the solder metal, it’s not allowed to floor-fuse the copper again-up plate.
• To avoid overheating or burn-by way of of thinner sheets, larger welding velocity has to be applied.
• Austenitic steels have only 30% of the thermal conductivity of non-alloyed steels.
• Their fusion level is decrease than that of non-alloyed steels, due to this fact austentic steels have to be welded with decrease warmth enter than non-alloyed steels.

Our stainless production range

While processing solely stainless instruments like metal brushes , pneumatic picks and so on are allowed, to be able to not endanger the passivation. It must be neglected to mark throughout the welding seam zone with oleaginous bolts or temperature indicating crayons. The high corrosion resistance of this stainless-steel is predicated on the formation of a homogeneous, compact passive layer on the surface.

Alloy 310 / 310s / 310h

These grades contain 25% chromium and 20% nickel, making them highly proof against oxidation and corrosion. Grade 310S is a decrease carbon model, much less susceptible to embrittlement and sensitisation in service.

Stainless metal 310/310S is an austenitic heat resistant alloy with glorious resistance to oxidation beneath mildly cyclic situations via 2000°F. Stainless 310 is usually used at cryogenic temperatures, with wonderful toughness to -450°F, and low magnetic permeability. The alloy does not contain molybdenum, so pitting resistance is quite poor. Grade 310/310S shall be sensitised to intergranular corrosion after service at temperatures in range °C.

Higher chromium content material imparts additional corrosion resistance. Nickel is primarily used to achieve a particular microstructure. In addition, it has a helpful effect on mechanical properties and sure kinds of corrosion.

We have thousands tons stock of stainless steel sheet and coil with various size and grade,mainly include austenitic stainless steel, martens stainless steel (including precipitation hardened stainless steel sheet & coil), ferritic stainless steel, and duplex stainless steel.

Characteristics of Stainless Steel Sheet and Plate:
High corrosion resistance
High strength
High toughness and impact resistance
Temperature resistance
High workability, including machining, stamping, fabricating and welding
Smooth surface finish that can be easily clean