2cr13 material is 1.4162 duplex stainless steel

We produce 2cr13 material ASTM/ASME Grade 304, Grade 304L,304h, 316, 316L, 316H, 316TI, 321, 321H, 309S, 309H, 310S, 310H, 410S, 2205, 904L, 2507, 254, gh3030, 625, 253MA, S30815, 317L, Type 317, 316lN, 8020, 800, 800H, C276, S32304 and others special requirement stainless steel grade.

 

2cr13 stainless steel plate has good wear resistance, hardness, and sufficient toughness. Bob Dozier’s general-objective D2 bladeD2 is a device metal utilized in industrial settings. Its high hardness and relatively excessive toughness also make it an excellent choice in cutlery. Though technically not a stainless-steel — at least 14% chromium, and D2 normally has 12% — it’s comparatively corrosion-resistant.

However, there are particular drawbacks to this pocket knife. There’s no locking mechanism that can stop the blade or device from closing when you’re utilizing it. Also, this does not have a one-handed opening mechanism.

	2cr13 material Chemical Composition (%)
Steel Grade	C	Si (≤)	Mn (≤)	P (≤)	S (≤)	Cr	Ni (≤)
2Cr13	0.16 – 0.25	1.00	1.00	0.040	0.030	12.00 – 14.00	0.60
3Cr13	0.26 – 0.35	1.00	1.00	0.040	0.030	12.00 – 14.00	0.60
	2cr13 material Mechanical Properties
Steel Grade	Tensile strength (MPa)	Yield strength (MPa)	Elongation %	Reduction in area %	Impact energy (J)	Hardness (quenching & tempering)	Hardness (Annealing)
2Cr13	≥640	≥440	≥20	≥50	≥63	≤ 192HB	≤ 223HB
3Cr13	≥735	≥540	≥12	≥40	≥24	≤ 217HB	≤ 235HB

A record of the best pocket knives ever would never be complete without a Swiss Army Knife in it. When it comes to multi-software pocket knives, there’s no other selection but this one. You get 33 functions that may allow you to carry out on a regular basis and not-so-on a regular basis duties. Whether it’s opening your next Amazon buy or unhooking your largest catch, the Swiss Champ has received your back.

2cr13 material– The Perfect Tool For Any Surrounding

ASTM,AISI,SUS,JIS,EN,DIN,GB,ASME,ETC 2cr13 material

• Other alloying parts contribute to grain refinement which improves blade energy and edge toughness and in addition permit for a finer, sharper edge.
• Edge retention in actual chopping tests exceeded blades manufactured from the 420 and 440 collections of stainless steel.
• The steadiness of carbon and chromium content material gives it an excessive diploma of corrosion resistance and in addition spectacular physical characteristics of energy and edge holding.
• Knifemakers like Bob Dozier have constructed their popularity on making a superior knife with D2.
• D2 continues to see use in knives; a search on BladeHQ brings up 1,690 out there knives in D2.

Our stainless production range

The steadiness of carbon and chromium content gives it an excessive degree of corrosion resistance and in addition spectacular physical traits of energy and edge holding. Edge retention in actual chopping tests exceeded blades made of the 420 and 440 series of stainless steel.

 

.004.0420HC – A greater carbon model of standard Type 420 martensitic stainless-steel. The Carbon content, combined with the high Chromium content, provides good abrasion resistance and edge-holding. This steel is to not be confused with standard 420 stainless steel. 420HC is a superb basic function knife steel when warmth-treated with our proprietary Paul Bos heat-deal with process.

Its best corrosion resistance is achieved when 420 is hardened and surface floor or polished. The higher carbon content material employed in 420 gives larger power and hardness over stainless grades 410 and 416. In the annealed situation, 420 is comparatively straightforward to machine, but when hardened to above 30 HRC, machining turns into harder.

The carbon content and lean alloy make this a shallow hardening steel with a quenched hardness between Rc depending on exact carbon content material. High carbon, high chromium steel was developed as a substitute for excessive pace steel in England within the early 20th century. These steels were similar to the modern D3 device metal with very excessive carbon (2.2%). The carbon was lowered to 1.5%, and additions of Mo and V had been made to improve the toughness and hardenability of the metal which was in use by 1934.

We have thousands tons of stock of stainless steel sheet and coil with various size and grade, mainly include austenitic stainless steel, martens stainless steel (including precipitation hardened stainless steel sheet & coil), ferritic stainless steel, and duplex stainless steel.

Characteristics of Stainless Steel Sheet and Plate:
High corrosion resistance
High strength
High toughness and impact resistance
Temperature resistance
High workability, including machining, stamping, fabricating and welding
A smooth surface finish that can be easily clean